How to Replace Fence without Removing Concrete

How to Replace Fence without Removing Concrete

How to replace fence without removing concrete

Replacing a fence post can be a difficult process, particularly if the original post was secured in place by concrete. Fortunately, the procedure is straightforward, and once you’ve mastered it, you’ll be able to replace anything from a single rotten beam to a whole fence. Repairing a fence post is time-consuming and labor-intensive, especially if the post is fixed in concrete. Rather than removing the concrete with the post, try removing the post and leaving the concrete in place to be replaced. It is entirely possible to remove a fence post, despite the fact that it may appear to be a difficult undertaking.

Remove any fence panels or wiring from around the post

Remove any bolts attaching the post to a wood fence panel or wire mesh to allow access to the post you want to remove. The following are some examples of fasteners. Nails driven into a wood panel through a post. A detachable panel is used to attach the post to the fence. Wire mesh is secured to the post by tension bands.

  1. On one side of the fence post, dig a hole

Break through the earth around the concrete base of the fence post with a shovel. Continue excavating until the dirt and concrete are separated by a half-circle. Dig a hole as deep as the concrete itself, if possible, to provide the post as much room as possible. Most posts will be satisfied with a semi-circular hole. If your pole is stubborn, try digging the rest out.

  1. To split up the surrounding ground, move the post back and forth

At first, your pole will resist, but it will ultimately begin to move. Continue wiggling the post until you can easily move it back and forth, indicating that the concrete base has been lost to the ground.

  1. By hand, raise sagging posts.

Some posts can be easily removed by hand, especially if they were not put properly. Simply grab the pole’s base and pull it out of the ground with your legs. Because concrete is so heavy, enlist the assistance of at least two friends.

  1. If your post is stuck, use a jack to free it.

Set a high-lift jack on top of a thick block or brick adjacent to your post. Wrap one end of a heavy chain around the base of the post and attach the other end to the jack. Pump the jack slowly when you’re finished. The extra force will aid in the removal of the post from the ground.  If the jack isn’t strong enough, attach the chain to something bigger, such as a power lift.

  1. Remove any remaining concrete and any posts from the hole

Remove any remaining wood splinters, concrete slivers, or other undesired materials from the hole before installing your replacement post. Run the shovel’s head along the inside border of the hole, pulling out any excess debris and smoothing everything up if necessary.

Post should be replaced

If you don’t use the same size post as the previous one, it won’t fit in the hole properly. You may need to sand down your new post if it is having trouble sliding into the concrete base. However, removing too much of the bottom of the post will make it more prone to breaking under strain. Make sure your new post is level and at the correct height. The post must be in the ground for at least 20 inches. The depth of your fence post will be determined by the fence’s height.

Close the Gap

You can begin filling in the gaps now that the old post has been removed, the hole has been cleared, and the new post has been set. This does not necessitate a great amount of product and can be accomplished with sand or concrete. Double-check that your post is level and at the correct height before pouring in the sand or concrete. While you fill the hole, have a friend, family member, or kind neighbor level the post. If you’re using sand, make sure the hole is completely filled and there’s no air left. If the sand shifts and the post lean, not only the post but the entire fence line could be damaged. If you decide to use concrete to fill the hole, make sure it is thoroughly mixed before putting it in.

Remove the fence and re-attach it.

You can start rebuilding your fence after the sand has been poured or the concrete has fully set. Make sure that all of the pieces are in their proper places and that no pieces were lost during the post replacement procedure. You can enjoy privacy in your yard with a robust fence once the fence has been renovated.

Concrete Removal and Post Removal

Although saving money by not having to repour concrete sounds appealing, the time and effort required to replace a post without removing it may be insufficient. Do you want to avoid the hassle of repairing a rotted or damaged fence post while keeping the concrete foundation intact? Continue reading to find out how to remove and replace a concrete-set fence post in the quickest way possible.

Destroy the Barrier

Remove the fence from the post that needs to be replaced with care. Keep track of how the fence should be reassembled and store each piece somewhere it won’t be misplaced.

Fence Reconstruction

You can start rebuilding your fence now that you have a stronger fence post installed. Ascertain that each piece is returned to its proper location and that no items are left behind Simply put, it’s that simple! There’s no need to spend hours with a crowbar or keeping an eye on a fire. By repairing both the fence post and the foundation at the same time, you can save some time and effort.

Leave a Comment